What the Watt Calculator Does
This Watt Calculator turns two simple electrical measurements — voltage and current — into two useful results: power in watts (W) and resistance in ohms (Ω). It is based on Ohm's law and the power equation, which apply universally to direct-current (DC) circuits and to the basic relationships taught in electronics worldwide (no country-specific rules are involved). Whether you are sizing a power supply, checking an appliance's load, or working on a hobby electronics project, this tool gives instant, accurate figures.
The Inputs You Enter
- Voltage (V): The potential difference across the component or circuit, measured in volts.
- Current (A): The flow of electric charge through the circuit, measured in amperes (amps).
Both values are read as numbers, so you can enter decimals such as 12 or 0.5. Make sure the two figures refer to the same point in the circuit for meaningful results.
The Formula Explained
The calculator applies two formulas at once:
- Power: $$P = \text{Voltage (V)} \times \text{Current (A)}$$
- Resistance: $$R = \frac{\text{Voltage (V)}}{\text{Current (A)}}$$
Power tells you how much energy the circuit uses per second, while resistance — derived directly from Ohm's law (\(V = I \times R\)) — tells you how much the circuit opposes the current. The tool also expresses your result as a percentage of a 1000 W (1 kW) scale for quick visualisation, capping the bar at 100%.
Worked Example
Suppose you have a device running at 12 V drawing 2 A:
- $$\text{Power} = 12 \times 2 = 24 \text{ watts}$$
- $$\text{Resistance} = 12 \div 2 = 6 \text{ ohms}$$
- $$\text{Visualisation} = \frac{24}{1000} \times 100 = 2.4\% \text{ of the 1 kW scale}$$
So this device consumes 24 W and presents 6 Ω of resistance.
More Worked Examples
Each example uses \(P = V \times I\) and \(R = V \div I\). The percentage is the power shown on a 1 kW (1000 W) scale, capped at 100%.
Example 1: 5 V USB device at 0.5 A
- Power: \(P = 5 \times 0.5 = \)2.5 W
- Resistance: \(R = 5 \div 0.5 = 10\) Ω
- On the 1 kW scale: \(2.5 \div 1000 = 0.25\%\)
Example 2: 230 V appliance at 4.35 A
- Power: \(P = 230 \times 4.35 = 1000.5\) W, or about 1000 W
- Resistance: \(R = 230 \div 4.35 \approx 52.9\) Ω
- On the 1 kW scale: \(1000.5 \div 1000 \approx 100\%\), so the gauge is effectively full.
Example 3: 120 V load at 10 A
- Power: \(P = 120 \times 10 = \)1200 W
- Resistance: \(R = 120 \div 10 = 12\) Ω
- On the 1 kW scale: \(1200 \div 1000 = 120\%\), which is capped at 100% because it is past the scale's maximum.
Typical Power Ratings of Common Devices
The wattages below are approximate typical values. Real products vary by model and operating mode. Current is calculated as \(I = P \div V\) and rounded, assuming a resistive load (power factor 1). Nominal mains voltages differ by country, for example about 120 V in North America and about 230 V in Europe and many other regions.
| Device | Approx. typical power | Current at 120 V | Current at 230 V |
|---|---|---|---|
| LED bulb | 5–15 W | 0.04–0.13 A | 0.02–0.07 A |
| Phone charger | 5–20 W | 0.04–0.17 A | 0.02–0.09 A |
| Laptop | 45–100 W | 0.38–0.83 A | 0.20–0.43 A |
| TV | 50–200 W | 0.42–1.67 A | 0.22–0.87 A |
| Microwave oven | 800–1500 W | 6.7–12.5 A | 3.5–6.5 A |
| Electric kettle | 1500–3000 W | 12.5–25 A | 6.5–13 A |
Kettles at the high end of this range are normally built for 230 V supplies. On 120 V circuits, a 25 A draw would exceed what a typical household outlet circuit is designed to carry, so 120 V kettles are generally rated lower.
Power Unit Conversions
| Unit | Equivalent in watts / other units |
|---|---|
| 1 milliwatt (mW) | 0.001 W |
| 1 kilowatt (kW) | 1000 W |
| 1 megawatt (MW) | 1,000,000 W |
| 1 watt (W) | ≈ 3.412 BTU/h |
| 1 horsepower (mechanical) | ≈ 745.7 W |
| 1 metric horsepower | ≈ 735.5 W |
| 1 watt (W) | = 1 joule per second (J/s) |
The watt is the SI unit of power. One watt means one joule of energy transferred each second, which is also one volt × one amp.
Frequently Asked Questions
What if I enter 0 amps? Power would correctly calculate as 0 W, but resistance (\(V \div A\)) cannot be computed because dividing by zero is undefined. Always enter a current greater than zero to get a valid resistance.
Does this work for AC circuits? The result is the apparent power for AC. True power in AC circuits with reactive loads also depends on the power factor, so for motors or transformers the actual wattage may be lower.
Why does the result cap at 100%? The percentage bar uses a fixed 1000 W reference for easy comparison. Any power above 1 kW simply shows as a full 100% bar, while the exact watt figure is still displayed.