What Is Capacitance?
Capacitance is a measure of a component's ability to store electric charge. It is defined as the ratio of the electric charge (Q) stored on a conductor to the potential difference (V) across it. The SI unit of capacitance is the farad (F), where one farad equals one coulomb per volt. Because a farad is a very large unit, practical capacitors are usually rated in microfarads (µF), nanofarads (nF), or picofarads (pF).
How to Use This Calculator
Enter the charge stored on the capacitor in coulombs and the voltage across it in volts. The calculator divides the charge by the voltage to return the capacitance in farads, and also converts the answer to microfarads for convenience. Make sure your inputs use consistent base units (coulombs and volts) for an accurate result.
The Formula Explained
The governing equation is \(C = Q / V\), where C is capacitance in farads, Q is charge in coulombs, and V is voltage in volts. Rearranging the equation lets you solve for any single variable: charge is \(Q = C \times V\), and voltage is \(V = Q / C\). This relationship is fundamental to circuit analysis, energy storage, and timing applications.
$$C = \frac{\text{Charge (C)}}{\text{Voltage (V)}}$$
Worked Example
Suppose a capacitor stores 0.001 coulombs of charge at 5 volts. Then $$C = 0.001 / 5 = 0.0002 \text{ farads},$$ which equals 200 microfarads. A capacitor holding more charge at the same voltage would have a proportionally higher capacitance.
Capacitance Unit Conversion Table
The farad (F) is the SI unit of capacitance, defined as one coulomb per volt. Most practical capacitors are far smaller than 1 F, so sub-units are used. Because \(C = Q/V\), enter charge in coulombs and voltage in volts to get farads.
| Unit | Symbol | Conversion to farads | Example |
|---|---|---|---|
| Farad | F | 1 F = 1 F | 1 F = 1 F |
| Millifarad | mF | 1 mF = 10-3 F | 4.7 mF = 0.0047 F |
| Microfarad | µF | 1 µF = 10-6 F | 100 µF = 0.0001 F |
| Nanofarad | nF | 1 nF = 10-9 F | 10 nF = 1 × 10-8 F |
| Picofarad | pF | 1 pF = 10-12 F | 22 pF = 2.2 × 10-11 F |
Charge units: 1 mC = 10-3 C, 1 µC = 10-6 C, and 1 nC = 10-9 C. For example, 250 µC = 0.00025 C and 50 nC = 5 × 10-8 C. Convert to coulombs before dividing by the voltage.
Typical Capacitor Values by Type
The ranges below are approximate and general. Exact limits depend on the manufacturer, voltage rating and package size.
| Capacitor type | Approximate capacitance range | Common uses |
|---|---|---|
| Ceramic | about 1 pF to 100 µF | High-frequency decoupling, bypassing, RF circuits, filtering, timing |
| Film | about 100 pF to 100 µF | Audio circuits, precision timing, power electronics, motor run and snubber applications |
| Aluminum electrolytic | about 0.1 µF to several 10,000 µF | Power supply smoothing, bulk energy storage, audio coupling |
| Tantalum | about 0.1 µF to 1000 µF | Compact bulk decoupling, portable electronics, stable low-leakage filtering |
| Supercapacitor | about 0.1 F to thousands of F | Energy backup, memory retention, burst power, energy harvesting |
Electrolytic and tantalum capacitors are polarized, so connect them with the correct polarity and stay within their voltage rating.
Capacitance for Different Charge and Voltage Combinations
Each row uses \(C = Q/V\) with Q converted to coulombs.
| Charge Q | Voltage V | Calculation | C (F) | C (µF) |
|---|---|---|---|---|
| 1 µC | 1 V | \(10^{-6} / 1\) | 1 × 10-6 F | 1 µF |
| 100 µC | 5 V | \(10^{-4} / 5\) | 2 × 10-5 F | 20 µF |
| 1 mC | 12 V | \(10^{-3} / 12\) | 8.33 × 10-5 F | 83.3 µF |
| 10 mC | 50 V | \(0.01 / 50\) | 0.0002 F | 200 µF |
Note: Capacitance is a property of the capacitor's geometry (plate area and spacing) and its dielectric material, not of the charge or voltage applied. For a fixed capacitor, C stays constant and the stored charge Q scales in proportion to V. For example, a 20 µF capacitor holds 100 µC at 5 V and 200 µC at 10 V. The rows above compare different capacitors, each described by its own Q and V pair.
FAQ
What unit should I use for charge? Use coulombs (C). One coulomb is a large amount of charge; small capacitors often store microcoulombs, so convert accordingly.
Why is my answer so small? One farad is enormous. Even a 200 µF capacitor is only 0.0002 F, so small decimal results in farads are normal.
Can I find voltage or charge instead? Yes. Rearrange \(C = Q / V\) to get \(Q = C \times V\) or \(V = Q / C\) depending on which variable you know.