What Is the Transmittance to Absorbance Calculator?
This calculator converts percent transmittance (%T) — the fraction of light that passes through a sample — into absorbance (A), a logarithmic measure of how much light a sample absorbs. Both quantities come from spectrophotometry and are central to UV-Vis analysis, the Beer-Lambert law, and many quantitative chemistry and biology assays. While transmittance is what a detector physically measures, absorbance is usually preferred for calculations because it is linearly proportional to concentration.
How to Use It
Enter the percent transmittance reading from your spectrophotometer (a value between 0 and 100). The calculator divides it by 100 to get the transmittance fraction and then applies the negative base-10 logarithm to return absorbance in absorbance units (AU). A value of 100%T gives an absorbance of 0, while smaller transmittance values yield higher absorbance.
The Formula Explained
The conversion uses $$A = -\log_{10}\left(\frac{\text{Transmittance (\%T)}}{100}\right)$$ The term \(\%T/100\) converts the percentage to a fraction between 0 and 1. Taking the base-10 logarithm of a fraction yields a negative number, so the leading minus sign makes absorbance positive. Because the relationship is logarithmic, each tenfold drop in transmittance adds 1 to the absorbance: \(10\%T = 1.0\ A\), \(1\%T = 2.0\ A\), and \(0.1\%T = 3.0\ A\).
Worked Example
Suppose a sample transmits 25% of the incident light. First convert to a fraction: \(25 / 100 = 0.25\). Then take the negative logarithm: $$A = -\log_{10}(0.25) = -(-0.60206) = 0.60206$$ So 25%T corresponds to an absorbance of about 0.602 AU.
%T to Absorbance Conversion Table
Each value below is computed from \(A = -\log_{10}(\%T/100)\), where the transmittance fraction is \(T = \%T/100\). Absorbance is rounded to 3 decimals.
| Transmittance (%T) | Transmittance fraction (T) | Absorbance (A) |
|---|---|---|
| 100 | 1.000 | 0.000 |
| 90 | 0.900 | 0.046 |
| 80 | 0.800 | 0.097 |
| 70 | 0.700 | 0.155 |
| 60 | 0.600 | 0.222 |
| 50 | 0.500 | 0.301 |
| 40 | 0.400 | 0.398 |
| 30 | 0.300 | 0.523 |
| 25 | 0.250 | 0.602 |
| 20 | 0.200 | 0.699 |
| 10 | 0.100 | 1.000 |
| 5 | 0.050 | 1.301 |
| 1 | 0.010 | 2.000 |
| 0.1 | 0.001 | 3.000 |
Worked check: for 50 %T, \(A = -\log_{10}(50/100) = -\log_{10}(0.5) = 0.301\). Every tenfold drop in transmittance adds exactly 1 to the absorbance.
Interpreting Your Absorbance Value
- A = 0 means no light is absorbed: 100 %T, so all the light reaching the sample passes through (relative to the blank).
- Unitless: absorbance is a logarithm of a ratio of intensities, so it has no true unit. It is often written as AU (absorbance units) by convention.
- A = 0.3 corresponds to about 50 %T, meaning roughly half the light is absorbed. This is because \(10^{-0.301} = 0.5\).
- Generally reliable working range: about 0.1 to 1.0 AU, which is roughly 80 %T down to 10 %T. Accuracy is usually best near 0.2 to 0.8 AU, roughly 63 %T to 16 %T.
- Low absorbance (below ~0.1 AU): very little light is absorbed, so small instrument noise and baseline drift make up a large fraction of the signal. Consider a more concentrated sample or a longer path length.
- High absorbance (above ~1.5 to 2 AU): very little light (below about 3 %T to 1 %T) reaches the detector. Stray light, detector limits and electronic noise cause readings to deviate from the Beer–Lambert law, so the response becomes nonlinear. Dilute the sample and re-measure, then multiply by the dilution factor.
To go back from absorbance to transmittance, use \(\%T = 100 \times 10^{-A}\). The exact limits of the linear range depend on the instrument and the sample, so check your spectrophotometer's specifications.
FAQ
What does 100%T mean? It means all light passes through with no absorption, giving an absorbance of exactly 0.
Why use absorbance instead of transmittance? Absorbance is directly proportional to concentration through the Beer-Lambert law, making linear calibration curves possible.
Can transmittance be 0%? A true 0%T would give infinite absorbance, which is not physically meaningful. Use a small positive value instead.