Asphalt Shingle Calculator

Asphalt Shingle Calculator

Growing AI Skill PRO

Enter Calculation

Formula

Bundles=⌈Roof Area (sq ft)×(1+Waste (%)100)100×Bundles per Square⌉\text{Bundles} = \left\lceil \frac{\text{Roof Area (sq ft)} \times \left(1 + \frac{\text{Waste (\%)}}{100}\right)}{100} \times \text{Bundles per Square} \right\rceil
Usage stats

Advertisement

Results

Shingle Bundles Needed
66
bundles
Roofing squares needed 22
Adjusted area (with waste) 2,200 sq ft

Report an error on this page

What Is the Asphalt Shingle Calculator?

The asphalt shingle calculator estimates how many shingle bundles and roofing squares you need to cover a roof. In roofing, one square equals 100 square feet of surface, and shingles are sold in bundles, with most three-tab and architectural shingles packed three bundles per square. Adding a waste factor accounts for cuts, ridges, valleys, and starter courses.

A 10 by 10 foot square of shingle roof shown as equal to three shingle bundles
One roofing square covers 100 sq ft and usually takes three bundles of standard 3-tab or architectural shingles.

How to Use It

Enter your total roof surface area in square feet (the actual sloped area, not the building footprint). Set a waste factor: 10% is typical for simple gable roofs, while 15% or more suits complex roofs with many hips and valleys. Choose the bundles per square for your product, then read the number of bundles and squares needed.

The Formula Explained

The calculator first inflates the area by the waste factor, converts it to squares, multiplies by bundles per square, and rounds up to whole bundles:

$$\text{Bundles} = \left\lceil \frac{A \times (1 + w/100)}{100} \times b \right\rceil$$

Here \(A\) = roof area in square feet, \(w\) = waste factor as a percent, and \(b\) = bundles per square. The ceiling function guarantees you never buy a fraction of a bundle.

Advertisement
Gable roof with measured planes and a small pile of cut-off shingle waste
Measure every roof plane to get total area, then add a waste allowance for cuts, starter rows, and ridge caps.

Worked Example

Suppose a roof measures 2000 sq ft with a 10% waste factor and 3 bundles per square:

$$\text{Adjusted area} = 2000 \times 1.10 = 2200\ \text{sq ft}$$ $$\text{Squares} = \frac{2200}{100} = 22$$ $$\text{Bundles} = \lceil 22 \times 3 \rceil = 66$$

So you would order 66 bundles, covering 22 squares.

Roof Pitch Multipliers: Converting Footprint to Sloped Area

The calculator needs the real sloped surface area of the roof. A plan measurement or the building's footprint is smaller than that. To convert, multiply the horizontal area (footprint plus overhangs) by a pitch multiplier. Roof pitch is written as rise over a 12-unit horizontal run, which is the usual convention in the US and Canada. The multiplier is the slope length per unit of horizontal run:

$$M = \sqrt{1 + \left(\frac{\text{rise}}{12}\right)^2}$$

For example, a 6/12 roof gives \(M = \sqrt{1 + 0.5^2} = \sqrt{1.25} \approx 1.118\).

Pitch (rise/12) Roof angle Multiplier
3/12 14.0° 1.031
4/12 18.4° 1.054
5/12 22.6° 1.083
6/12 26.6° 1.118
7/12 30.3° 1.158
8/12 33.7° 1.202
9/12 36.9° 1.250
10/12 39.8° 1.302
11/12 42.5° 1.357
12/12 45.0° 1.414

Example: a house has a 1,500 sq ft footprint including overhangs and a 6/12 roof. The sloped area is \(1{,}500 \times 1.118 = 1{,}677\) sq ft, and that is the number to enter as the roof area. With a 10% waste factor and 3 bundles per square:

$$\left\lceil \frac{1677 \times 1.10}{100} \times 3 \right\rceil = \lceil 18.447 \times 3 \rceil = \lceil 55.34 \rceil = 56$$

That comes to 56 bundles. The multiplier assumes every roof plane has the same pitch. If sections have different pitches, work out each one separately and add the sloped areas together.

Advertisement

Bundles per Square by Shingle Type

A roofing "square" is 100 sq ft of roof surface, a unit used mainly in the US and Canada. How many bundles cover one square depends on how thick and heavy the shingle is. The figures below are typical for North American products:

Shingle type Typical bundles per square Notes
3-tab (strip) 3 Flat, single-layer shingle. About 33.3 sq ft per bundle.
Standard architectural / laminated (dimensional) 3 The most common type today. Most lines are packed 3 bundles per square.
Heavy or designer laminated 4–5 Thicker, multi-layer premium lines. Fewer shingles fit in each bundle.
Hip-and-ridge cap shingles Sold by linear feet Each bundle typically covers about 20–35 linear feet of hip or ridge, depending on the product and exposure.

In the calculator, choose 3 for 3-tab and most architectural shingles, and 4 for heavier laminated lines. If a product is packed 5 bundles per square, either take the squares figure from the calculator and multiply by 5, or ask your supplier. Hip-and-ridge caps are not counted in the area-based estimate. Measure the total length of your hips and ridges in linear feet, then divide by the per-bundle coverage of the cap product you choose.

Always check the bundle wrapper. Manufacturers print the coverage (sq ft per bundle and bundles per square) and the recommended exposure on each package. That printed figure overrides the typical values above, because coverage varies between brands and product lines.

FAQ

What is a roofing square? A square is 100 square feet of roof surface, the standard unit roofers use for estimating and pricing.

How much waste should I add? Use about 10% for straightforward roofs and 15% or more for roofs with many valleys, hips, or dormers.

Why round bundles up? Shingles ship in whole bundles, so the result is rounded up to ensure full coverage plus a small cushion.

Last updated:

Most popular in Industry-Specific

View all Industry-Specific calculators