Cone Lateral Surface Area Calculator

Cone Lateral Surface Area Calculator

Popular AI Skill PRO
Cone
Worked stepsStep 4 of 4

Lateral area AL=πrsA_L = \pi r s

Download figure
Figure data
Radius3
Height4
Lateral area47.12
Slant height5
Cone in the Library: formulas and every calculator

Enter Calculation

Formula

A=π·Radius·Radius2+Height2A = \pi \cdot \text{Radius} \cdot \sqrt{\text{Radius}^{2} + \text{Height}^{2}}
Usage stats

Advertisement

Results

Lateral Surface Area
47.12 square units
Input Radius 3 units
Input Height 4 units
Slant Height 5 units
Arc Length (Base Perimeter) 18.85 units
Sector Angle 360°
Lateral Surface Area 47.12 square units

Report an error on this page

What This Calculator Does

The Cone Lateral Surface Area Calculator works out the curved (slanted) surface of a right circular cone — the area you would get if you peeled off the cone's side and laid it flat. It does not include the flat circular base. You simply enter two values, the radius and the height, and the tool returns the lateral surface area along with several helpful supporting figures.

Cone showing radius r, height h, and slant height l with the lateral surface highlighted
The lateral surface is the curved side of the cone, defined by radius, height, and slant height.

The Inputs You Provide

  • Radius: the distance from the centre of the circular base to its edge.
  • Height: the perpendicular (vertical) distance from the base to the tip of the cone.

Both values should use the same unit (cm, m, inches, etc.). The result will be in those units squared.

The Formula Explained

The lateral surface area uses the formula:

A = π r √(r² + h²)

The term √(r² + h²) is the slant height (l) — the straight-line distance from the base edge up to the apex, found using the Pythagorean theorem. So the formula can also be written A = π r l. The calculator computes this slant height for you first, then multiplies by π and the radius.

Behind the scenes the tool also reports two related geometry values: the arc length (the perimeter of the base, 2πr) and the sector angle, which is the angle of the flat sector you would get when unrolling the curved surface.

Advertisement
Cone unrolled into a flat sector showing slant height as the sector radius
Unrolling the cone's side produces a flat sector whose area equals the lateral surface area.

Worked Example

Suppose a cone has a radius of 3 and a height of 4.

  • Slant height = √(3² + 4²) = √(9 + 16) = √25 = 5
  • Lateral area = π × 3 × 5 = 15π ≈ 47.12 square units
  • Arc length (base perimeter) = 2 × π × 3 ≈ 18.85 units

So this cone has a curved surface area of about 47.12 square units.

Lateral Surface Area for Different Cone Sizes

The lateral (curved) surface area of a right circular cone is \(A = \pi r \sqrt{r^2 + h^2}\), where \(r\) is the base radius and \(h\) is the perpendicular height. The table below applies this formula to several sizes. Lengths are in any single unit, and areas are in that unit squared. Values are rounded to 2 decimals.

Radius (r) Height (h) Slant height (l = √(r²+h²)) Lateral area (πrl)
3 4 5.00 47.12
5 12 13.00 204.20
6 8 10.00 188.50
10 5 11.18 351.24
2 10 10.20 64.08

Doubling both dimensions

The cone (3, 4) has a lateral area of 47.12. Doubling both dimensions gives the cone (6, 8), with a lateral area of 188.50. The ratio is \(188.50 / 47.12 \approx 4\).

This happens because doubling \(r\) and \(h\) also doubles \(l\). The formula \(\pi r l\) then becomes \(\pi (2r)(2l) = 4\pi r l\). In general, scaling every length by a factor \(k\) scales area by \(k^2\).

Advertisement

How to Calculate Cone Lateral Area by Hand

  1. Measure \(r\) and \(h\) in the same unit. Convert first if needed, for example both in centimeters. Use the radius (half the base diameter) and the perpendicular height from the base to the apex.
  2. Compute the slant height: \(l = \sqrt{r^2 + h^2}\).
  3. Multiply: \(A = \pi \cdot r \cdot l\).
  4. State the units squared, such as cm² or m².

Worked example: r = 3, h = 4

\(l = \sqrt{3^2 + 4^2} = \sqrt{9 + 16} = \sqrt{25} = 5\)

\(A = \pi \cdot 3 \cdot 5 = 15\pi \approx\) 47.12 square units.

Optional extras

  • Total surface area (lateral area plus the circular base): \(A_{\text{total}} = \pi r (l + r)\). For the example, \(\pi \cdot 3 \cdot (5 + 3) = 24\pi \approx 75.40\).
  • Sector angle of the unrolled lateral surface (a circular sector of radius \(l\)): \(\theta = 360^\circ \cdot \dfrac{r}{l}\), or \(\theta = \dfrac{2\pi r}{l}\) in radians. For the example, \(360^\circ \cdot 3/5 = 216^\circ\).
  • If the slant height is given instead of the height, skip step 2 and use \(A = \pi r l\) directly. If you know \(l\) and \(h\) but not \(r\), find \(r = \sqrt{l^2 - h^2}\). For example, \(l = 13\) and \(h = 12\) give \(r = \sqrt{169 - 144} = 5\).

Frequently Asked Questions

Does this include the base of the cone? No. This is the lateral (side) surface only. To get the total surface area, add the base circle area πr².

What is the difference between height and slant height? Height is the vertical distance to the tip; slant height runs along the sloped surface. The calculator derives slant height from your height and radius automatically.

What units should I use? Any unit works, as long as radius and height match. The area is returned in that unit squared.

Last updated:

Most popular in Geometry

View all Geometry calculators