Motorcycle Gear Ratio Calculator

Motorcycle Gear Ratio Calculator

Leading AI Skill PRO

Enter Calculation

Formula

v=NeRt×C×601000where{Rt=Primary×Gear×Rear TeethFront TeethNe=Engine RPMC=Tire Circumference (m)\begin{gathered} v = \frac{N_e}{R_t} \times C \times \frac{60}{1000} \\[1.5em] \text{where}\quad \left\{ \begin{aligned} R_t &= \text{Primary} \times \text{Gear} \times \dfrac{\text{Rear Teeth}}{\text{Front Teeth}} \\ N_e &= \text{Engine RPM} \\ C &= \text{Tire Circumference (m)} \end{aligned} \right. \end{gathered}
Usage stats

Advertisement

Results

Final Drive Ratio
3.000
rear ÷ front teeth
Total reduction (primary × gear × final) 6.000 : 1
Wheel speed at given RPM 1,000 rpm
Road speed at given RPM 114.0 km/h

Report an error on this page

What this calculator does

The Motorcycle Gear Ratio Calculator turns your front and rear sprocket teeth counts into the numbers that actually matter on the road: the final drive ratio and the road speed your bike reaches at a given engine RPM. It lets you preview a sprocket swap before you buy, so you can trade top speed for acceleration (or the reverse) with confidence.

Small front sprocket linked by a chain to a larger rear sprocket
The final drive ratio is the rear sprocket's tooth count divided by the front sprocket's tooth count.

How to use it

Enter the front (countershaft) sprocket teeth, the rear sprocket teeth, your primary drive ratio, the gearbox ratio for the gear you want to analyse, the rear tire circumference in metres, and an engine RPM. The tool returns the final drive ratio, the total reduction, the wheel speed, and the resulting road speed in km/h.

The formula explained

The final drive ratio depends only on the two sprockets, where \(T_{rear}\) is rear teeth and \(T_{front}\) is front teeth:

$$\text{FDR} = \frac{T_{rear}}{T_{front}}$$

Road speed also needs the primary ratio \(R_{p}\), gearbox ratio \(R_{g}\), tire circumference \(C\) in metres, and engine speed in RPM:

$$v = \frac{\text{RPM}}{R_{p} \times R_{g} \times \text{FDR}} \times C \times \frac{60}{1000}$$

A larger rear sprocket (or smaller front) raises the FDR, giving quicker acceleration but lower top speed per RPM.

Advertisement
Drivetrain from engine through primary drive, gearbox and chain sprockets to the rear wheel
Engine RPM is reduced by the primary drive, the selected gear and the sprockets in turn, and the tire circumference turns wheel revolutions into road speed.

Worked example

Take a 15T front, 45T rear, primary ratio 2.0, top gear 1.0, tire circumference 1.9 m, at 6000 RPM:

$$\text{FDR} = \frac{45}{15} = 3.0$$$$R_{total} = 2.0 \times 1.0 \times 3.0 = 6.0$$$$n_{wheel} = \frac{6000}{6.0} = 1000\ \text{rpm}$$$$v = 1000 \times 1.9 \times \frac{60}{1000} = 114\ \text{km/h}$$
Advertisement
Comparison of a short gearing sprocket setup and a tall gearing sprocket setup
A bigger rear sprocket or smaller front sprocket gives quicker acceleration, and the opposite change raises top speed at the same RPM.

Sprocket Swap Comparison: Acceleration vs Top Speed

Every row below uses the article's baseline bike: primary ratio 2.0, top gear 1.0, tire circumference 1.9 m and 6000 RPM, with stock sprockets of 15/45. The final drive ratio (FDR) is rear teeth ÷ front teeth. The total ratio is \(R_t = 2.0 \times 1.0 \times \text{FDR}\), and road speed comes from the formula below.

$$v = \frac{N_e}{R_t} \times C \times \frac{60}{1000}$$

To find the RPM needed for a set speed, rearrange it:

$$N_e = \frac{v \times R_t \times 1000}{C \times 60}$$

A higher FDR gives stronger acceleration, a lower road speed at any given RPM and more revs at cruising speed. A lower FDR does the opposite.

Setup Front teeth Rear teeth FDR Change vs stock Speed at 6000 RPM (km/h) Speed at 6000 RPM (mph) RPM for 100 km/h
Stock 15 45 3.00 0.00% 114.00 70.84 5263
−1 front 14 45 3.21 +7.14% 106.40 66.11 5639
+1 front 16 45 2.81 −6.25% 121.60 75.56 4934
+2 rear 15 47 3.13 +4.44% 109.15 67.82 5497
−2 rear 15 43 2.87 −4.44% 119.30 74.13 5029
−1 front, +2 rear 14 47 3.36 +11.90% 101.87 63.30 5890

Example for the stock row: \(R_t = 2.0 \times 1.0 \times 3.00 = 6.00\), so \(v = \frac{6000}{6.00} \times 1.9 \times 0.06 = 114\) km/h. Then \(114 \times 0.621371 = 70.84\) mph.

One front tooth is worth about three rear teeth. On this bike, one tooth off the front sprocket raises the FDR by 7.14%. Two extra teeth on the rear raise it by only 4.44%. Three extra rear teeth (15/48, FDR 3.20) would raise it by 6.67%, close to the effect of the one front tooth. The reason is that each front tooth is 1/15 of a small sprocket, while each rear tooth is only 1/45 of a large one. Change the front sprocket for big steps and the rear sprocket for fine tuning. Combining both changes adds up, as the 14/47 row shows: nearly 12% shorter gearing. Remember that changing the total tooth count may also mean a different chain length.

FAQ

Does adding teeth to the rear sprocket make me faster? It increases acceleration and engine braking but lowers top speed for a given RPM, because the final drive ratio goes up.

Where do I find the primary and gearbox ratios? They are listed in your service manual; many street bikes have a primary near 2.0 and a top gear near 1.0.

How do I get tire circumference? Roll the loaded rear wheel one full turn and measure the distance, or multiply the tire diameter by \(\pi\).

Last updated:

Most popular in Industry-Specific

View all Industry-Specific calculators