Pipe Flow Calculator

Pipe Flow Calculator

Growing AI Skill PRO

Enter Calculation

Formula

Q=π4·Diameter (m)2·Velocity (m/s)Q = \frac{\pi}{4} \cdot \text{Diameter (m)}^{2} \cdot \text{Velocity (m/s)}
Usage stats

Advertisement

Results

Volumetric Flow Rate
0.011781
cubic metres per second (m³/s)
Cross-sectional area 0.007854 m²
Flow rate 11.78 L/s
Flow rate 42.41 m³/h

Report an error on this page

What is the Pipe Flow Calculator?

This calculator finds the volumetric flow rate of a fluid moving through a round pipe. Given the pipe's inner diameter and the average flow velocity, it returns how much volume passes a cross-section each second, expressed in cubic metres per second (m³/s), litres per second (L/s) and cubic metres per hour (m³/h). It is a universal physics tool that applies to water, oil, air and any incompressible fluid in any country.

How to use it

Enter the pipe's inner diameter in metres (not the nominal or outer size) and the average flow velocity in metres per second. The calculator computes the circular cross-sectional area, multiplies it by the velocity, and converts the result to several common units.

Diagram deriving circular area from diameter for the flow formula
The cross-sectional area \(A\) is computed from the diameter as \(\frac{\pi}{4} \cdot d^{2}\).

The formula explained

The flow rate is the product of the cross-sectional area and the average velocity:

$$Q = A \times v$$ where $$A = \frac{\pi}{4} \times d^{2}$$

Here \(Q\) is the volumetric flow rate (m³/s), \(A\) is the pipe's internal area (m²), \(d\) is the inner diameter (m), and \(v\) is the average velocity (m/s). The \(\frac{\pi}{4} \cdot d^{2}\) term is simply the area of a circle written using the diameter instead of the radius.

Advertisement

Worked example

Suppose a pipe has an inner diameter of 0.1 m and the fluid flows at 2 m/s. The area is $$A = \frac{\pi}{4} \times 0.1^{2} = 0.0078539816 \text{ m}^{2}$$ The flow rate is $$Q = 0.0078539816 \times 2 = 0.0157079633 \text{ m}^{3}/\text{s}$$ which equals about 15.71 L/s or 56.55 m³/h.

Cross-section of a round pipe showing inner diameter and fluid velocity arrows
Flow rate equals the pipe's cross-sectional area times the average fluid velocity.

Typical Flow Velocities in Pipes

The velocity you enter strongly affects the result. These are commonly cited design velocity ranges:

Service Typical velocity (m/s)
Water supply / distribution 0.5 – 2.0
Pump suction line 0.5 – 1.5
Pump discharge line 1.5 – 3.0
Gravity drainage 0.6 – 3
Fuel / oil lines 1 – 2
Compressed air 6 – 20

Note: these are general engineering rules of thumb, not limits. Recommended values vary by applicable standard, pipe material, fluid viscosity, noise, erosion and pressure-drop limits, and project specification. Always check the relevant code or a qualified engineer for actual design.

Advertisement

Flow Rate for Common Pipe Sizes

Using \(Q = \frac{\pi}{4}\,d^{2}\,v\) with a fixed velocity of \(v = 1.5\) m/s and inner diameter \(d\) in metres:

Inner diameter (m) Area (m²) Q (L/s) Q (m³/h)
0.025 0.000490874 0.7363 2.651
0.05 0.00196350 2.945 10.60
0.1 0.00785398 11.78 42.41
0.2 0.0314159 47.12 169.6
0.3 0.0706858 106.0 381.7

Example for d = 0.1 m: \(Q = \frac{\pi}{4}\times 0.1^{2}\times 1.5 = 0.011781\) m³/s = 11.78 L/s, and \(0.011781 \times 3600 = 42.41\) m³/h.

Because flow depends on \(d^{2}\), doubling the diameter quadruples the flow at the same velocity (0.05 m → 0.1 m: 2.945 → 11.78 L/s). Use the actual inner diameter, not the nominal size, for accurate results.

FAQ

Should I use inner or outer diameter? Always use the inner (bore) diameter — that is the space the fluid actually flows through.

Does this account for friction or pressure drop? No. This is a continuity-based flow rate (\(Q = A \cdot v\)). It does not model head loss; use the Hazen-Williams or Darcy-Weisbach equations for that.

How do I convert to gallons or other units? 1 m³/s equals 1000 L/s; multiply L/s by 0.2642 for US gallons per second, or by 15.85 for US gallons per minute.

Last updated:

Most popular in Physics and Engineering

View all Physics and Engineering calculators