Strike Water Calculator

Strike Water Calculator

Emerging AI Skill PRO

Enter Calculation

Formula

Tstrike=0.2Ratio (qt/lb)(Target Temp (°F)−Grain Temp (°F))+Target Temp (°F)T_{\text{strike}} = \frac{0.2}{\text{Ratio (qt/lb)}} \left( \text{Target Temp (°F)} - \text{Grain Temp (°F)} \right) + \text{Target Temp (°F)}

Example

Tstrike=0.21.5(152−70)+152≈162.9T_{\text{strike}} = \frac{0.2}{1.5} \left( 152 - 70 \right) + 152 \approx 162.9
Show calculation steps (1)
  1. Strike Water Volume (qt and gal)

    Vqt=Ratio (qt/lb)×Grain Weight (lb)Vgal=Ratio (qt/lb)×Grain Weight (lb)4\begin{gathered} V_{\text{qt}} = \text{Ratio (qt/lb)} \times \text{Grain Weight (lb)} \\[1.5em] V_{\text{gal}} = \frac{\text{Ratio (qt/lb)} \times \text{Grain Weight (lb)}}{4} \end{gathered}

    Volume in quarts = ratio x grain weight; gallons = quarts / 4.

Usage stats

Advertisement

Results

Strike Water Temperature
162.9
°F
Strike Water Volume (quarts) 15.00 qt
Strike Water Volume (gallons) 3.75 gal

Report an error on this page

What is a Strike Water Calculator?

In all-grain brewing, strike water is the hot water you add to your crushed grain to start the mash. Because the room-temperature grain absorbs heat, you must heat the water above your target mash temperature so the combined mixture settles at the right spot. This calculator tells you both the strike water temperature and the volume to collect, so your mash lands in the enzyme-active range on the first try.

Hot strike water poured over cool grain in a mash tun with thermometers showing temperature difference
Strike water is added hot so it settles to the target mash temperature after mixing with cooler grain.

How to use it

Enter your grain weight in pounds, your desired water-to-grain ratio (mash thickness) in quarts per pound, the current temperature of your dry grain, and your target mash temperature. Typical ratios run from 1.25 to 1.75 qt/lb, and most single-infusion mashes target 148 to 158 °F. Click calculate to get the strike temperature and water volume.

The formula explained

The strike temperature comes from a heat-balance equation. With \(r\) = water-to-grain ratio in qt/lb, \(T_1\) = initial grain temperature, and \(T_2\) = target mash temperature:

$$\text{Strike Temp} = \frac{0.2}{r}\left(T_2 - T_1\right) + T_2$$

The constant \(0.2\) is the ratio of the specific heat of grain to that of water. The strike water volume is simply \(V = r \times W\), where \(W\) is grain weight in pounds; dividing quarts by 4 gives gallons.

Advertisement
Diagram showing grain temperature T1, water temperature T2, and ratio r combining into strike temperature
The formula combines grain temperature, target mash temperature, and the water-to-grain ratio.

Worked example

For 10 lb of grain at a 1.5 qt/lb ratio, grain at 70 °F, targeting a 152 °F mash:

$$\text{Strike Temp} = \frac{0.2}{1.5}\left(152 - 70\right) + 152 = 162.9\,\text{°F}$$

$$V = 1.5 \times 10 = 15\ \text{qt} = 3.75\ \text{gal}$$

FAQ

Why heat water above the mash temperature? The cool grain and mash tun pull heat out of the water, so the mix equilibrates below the water temperature.

Does the calculator account for the mash tun? No, it assumes a preheated tun. If your tun is cold, add roughly 2 to 4 °F to the strike temperature.

What ratio should I pick? Around 1.25 to 1.5 qt/lb is a common, balanced mash thickness for most beer styles.

Last updated:

Most popular in Hobby and Craft

View all Hobby and Craft calculators