GPM Flow Rate Calculator (Pipe)

GPM Flow Rate Calculator (Pipe)

Popular AI Skill PRO

Enter Calculation

Formula

GPM=Velocity×π(Diameter24)2×448.831\text{GPM} = \text{Velocity} \times \pi \left(\frac{\text{Diameter}}{24}\right)^{2} \times 448.831
Usage stats

Advertisement

Results

Volumetric Flow Rate
48.96
gallons per minute (GPM)
Flow Velocity 5 ft/s
Pipe Cross-Section Area 0.021817 ft²

Report an error on this page

What Is the GPM Flow Rate Calculator?

This calculator finds the volumetric flow rate through a round pipe in gallons per minute (GPM) using the flow velocity and the pipe's inside diameter. It applies the standard relationship that flow rate equals velocity multiplied by the pipe's cross-sectional area, then converts cubic feet per minute into US gallons per minute with the factor 448.831.

How to Use It

Enter the flow velocity in feet per second (ft/s) and the inside diameter of the pipe in inches. The calculator converts the diameter to feet, computes the circular cross-sectional area, and returns the flow rate in GPM along with the area used.

The Formula Explained

The core equation is $$\text{GPM} = V \times A \times 448.831$$ where V is velocity in ft/s and A is the pipe area in square feet. The area comes from \(A = \pi \times r^2\), with \(r\) being the inside radius in feet. Because diameter is entered in inches, it is divided by 12 to convert to feet before halving. The constant 448.831 converts cubic feet per minute (ft³/min) to US gallons per minute, since 1 ft³ = 7.48052 gallons and there are 60 seconds in a minute (\(7.48052 \times 60 = 448.831\)).

Advertisement
Cross-section of a circular pipe showing inside diameter and flow velocity arrow
Flow rate combines pipe cross-sectional area (from inside diameter) with flow velocity.

Worked Example

Suppose water moves at 5 ft/s through a 2-inch inside-diameter pipe. The radius is \((2 \div 12) \div 2 = 0.08333\) ft, so the area is \(\pi \times 0.08333^2 \approx 0.021817\) ft². Then $$\text{GPM} = 5 \times 0.021817 \times 448.831 \approx 48.96 \text{ gallons per minute}.$$

Diagram breaking GPM formula into velocity, area, and conversion factor
GPM = velocity × cross-sectional area × 448.831.

Typical Flow Velocity Ranges in Piping

Designers usually choose a pipe size by picking a target velocity and then checking the resulting flow, pressure drop, noise and erosion. The ranges below are commonly cited rules of thumb in feet per second (ft/s), not fixed limits.

Application Typical velocity (ft/s)
Water supply / distribution mains about 3–8
Pump suction piping about 1–5
Pump discharge piping about 4–10
Building domestic copper piping often limited to about 5–8

These are general engineering guidelines. The right value depends on the pipe material, the fluid (viscosity, solids, temperature), noise limits, erosion and corrosion concerns, and allowable pressure drop. Typical sources are plumbing and mechanical codes, pipe and pump manufacturer guidance, and engineering handbooks. Check the rules that apply to your jurisdiction and project before you size real piping.

GPM by Pipe Size and Velocity

Values use \(\text{GPM} = V \times \pi \left(\frac{d}{24}\right)^{2} \times 448.831\), where \(V\) is in ft/s and \(d\) is the inside diameter in inches. This simplifies to about \(\text{GPM} \approx 2.448 \times V \times d^{2}\). For example, a 2 in pipe at 5 ft/s: \(5 \times \pi \times (2/24)^2 \times 448.831 \approx 48.96\) GPM.

Inside diameter (in) 3 ft/s 5 ft/s 8 ft/s
0.5 1.84 3.06 4.90
0.75 4.13 6.89 11.02
1 7.34 12.24 19.58
1.5 16.52 27.54 44.06
2 29.38 48.96 78.34
3 66.10 110.16 176.26
4 117.50 195.84 313.34
6 264.38 440.64 705.02

Flow scales with the square of the diameter and linearly with velocity. Doubling the diameter at the same velocity quadruples the GPM, and doubling the velocity in the same pipe doubles it. Use the actual inside diameter, which differs from the nominal size and depends on the pipe schedule or tube type.

Advertisement

Flow Rate Unit Conversions

Multiply a flow in US gallons per minute (GPM) by the factor below. These factors are for the US liquid gallon.

1 US GPM equals Unit
3.78541 L/min
0.227125 m³/h
0.0630902 L/s
0.002228 ft³/s
0.133681 ft³/min
0.832674 Imperial GPM
34.2857 barrels per day (42-gallon US barrel)

Example rows for 100 US GPM:

Unit Value for 100 GPM
L/min 378.541
m³/h 22.7125
L/s 6.30902
ft³/min 13.3681
Imperial GPM 83.2674
Barrels per day 3,428.57

FAQ

Does this work for any liquid? Yes. The geometry-based calculation is fluid-independent; it depends only on velocity and pipe size, not on the fluid's density or viscosity.

Is the diameter inside or outside? Use the inside (internal) diameter of the pipe, since that is the actual flow path. Nominal pipe sizes can differ from the true internal diameter.

What units does GPM use here? The result is in US gallons per minute. For Imperial (UK) gallons, multiply the result by approximately 0.8327.

Last updated:

Most popular in Physics and Engineering

View all Physics and Engineering calculators