BIS Capital Adequacy Ratio Calculator

BIS Capital Adequacy Ratio Calculator

Leading AI Skill PRO

Enter Calculation

Formula

CAR=Tier 1 (M)+Tier 2 (M)RWA (M)×100\text{CAR} = \frac{\text{Tier 1 (M)} + \text{Tier 2 (M)}}{\text{RWA (M)}} \times 100

Example

CAR=50+301000×100=8.00\text{CAR} = \frac{50 + 30}{1000} \times 100 = 8.00
Show calculation steps (1)
  1. Tier 1 Capital Ratio (%)

    Tier 1 Ratio=Tier 1 (M)RWA (M)×100\text{Tier 1 Ratio} = \frac{\text{Tier 1 (M)}}{\text{RWA (M)}} \times 100

    Tier 1 capital divided by Risk-Weighted Assets, times 100

Usage stats

Advertisement

Results

BIS Capital Adequacy Ratio (CAR)
8.00%
total capital as a percent of risk-weighted assets
Total Capital (Tier 1 + Tier 2) 80
Tier 1 Capital Ratio 5.00%
Regulatory minimum (Basel) 8.00%

Report an error on this page

What is the BIS Capital Adequacy Ratio?

The BIS capital adequacy ratio (CAR), defined under the Basel framework of the Bank for International Settlements, measures how much regulatory capital a bank holds relative to its risk-weighted assets (RWA). It is a core solvency indicator: a higher ratio means a bank can absorb more losses before becoming insolvent. Regulators typically require a minimum total CAR of 8%.

The formula

The ratio adds Tier 1 (core) capital and Tier 2 (supplementary) capital, then divides by risk-weighted assets:

$$\text{CAR} = \frac{\text{Tier 1} + \text{Tier 2}}{\text{RWA}} \times 100\%$$

Here \(\text{Tier 1}\) is core capital such as common equity and retained earnings, \(\text{Tier 2}\) is supplementary capital such as subordinated debt and certain reserves, and \(\text{RWA}\) is total assets each weighted by its credit, market, and operational risk.

Diagram showing two capital blocks stacked over a risk-weighted assets block as a fraction
The CAR combines Tier 1 and Tier 2 capital divided by risk-weighted assets.

How to use this calculator

Enter the bank's Tier 1 capital, Tier 2 capital, and total risk-weighted assets in the same currency units (for example, millions). The calculator returns the total CAR, the total capital figure, and the Tier 1 capital ratio so you can compare each against regulatory minimums.

Advertisement

Worked example

Suppose a bank has \(\text{Tier 1}=50\), \(\text{Tier 2}=30\), and \(\text{RWA}=1000\) (millions). Total capital is \(50+30=80\), so:

$$\text{CAR} = \frac{50 + 30}{1000} \times 100\% = 8.00\%$$

The Tier 1 ratio is \(\frac{50}{1000}\times 100\% = 5.00\%\). The bank exactly meets the 8% total minimum.

Semicircular gauge with needle pointing past a threshold into the green zone
Compare the resulting ratio against the regulatory minimum threshold.

Basel III Minimum Capital Requirements and Buffers

The capital adequacy ratio (CAR) is measured against the minimum standards set by the Basel III framework, which is issued by the Basel Committee on Banking Supervision (BCBS) at the Bank for International Settlements (BIS). All figures below are expressed as a percentage of risk-weighted assets (RWA). These are the internationally agreed minimums; national regulators (for example, the EU, the UK PRA, or the US federal banking agencies) implement them in local law and may set higher requirements, so the exact thresholds a specific bank must meet depend on its home jurisdiction.

Requirement Level (% of RWA) Source
Common Equity Tier 1 (CET1) minimum 4.5% Basel III / BCBS
Tier 1 capital minimum 6.0% Basel III / BCBS
Total capital minimum (Tier 1 + Tier 2) 8.0% Basel III / BCBS
Capital conservation buffer (CET1) 2.5% Basel III / BCBS
Countercyclical buffer (CET1, jurisdiction-set) 0% – 2.5% Basel III / BCBS (set by national authorities)
G-SIB / systemically important surcharge (CET1) 1.0% – 3.5% (bucket-dependent) BCBS G-SIB framework / FSB
Effective total capital requirement (8% minimum + 2.5% conservation buffer) 10.5% Basel III / BCBS

The 8% total minimum is the hard floor. Adding the 2.5% capital conservation buffer gives an effective total requirement of 10.5% of RWA. Where a countercyclical buffer (up to 2.5%) or a G-SIB surcharge (1.0%–3.5% depending on the assigned bucket) applies, those amounts — which must be met with CET1 capital — are added on top, so the largest global banks face materially higher effective requirements.

Advertisement

FAQ

What is a good CAR? Basel III sets a minimum total capital ratio of 8%, but many regulators add buffers, so well-capitalized banks often report 12% or more.

What is the difference between Tier 1 and Tier 2? Tier 1 is high-quality core capital available to absorb losses on a going-concern basis; Tier 2 is lower-quality supplementary capital used mainly in wind-down scenarios.

Why use risk-weighted assets instead of total assets? RWA scales each exposure by its riskiness, so safer assets require less capital backing than riskier ones.

Last updated:

Most popular in Banking Services

View all Banking Services calculators