Newton Meter Torque Calculator

Newton Meter Torque Calculator

Leading AI Skill PRO

Enter Calculation

Formula

τ=Force (N)×Distance (m)\tau = \text{Force (N)} \times \text{Distance (m)}

Example

τ=400×0.25=100\tau = 400 \times 0.25 = 100
Usage stats

Advertisement

Results

Torque
100
newton-metres (Nm)
Force 400 N
Distance / lever arm 0.25 m

Report an error on this page

What Is a Newton Meter Torque Calculator?

Torque is the rotational equivalent of force — it measures the turning effect produced when a force is applied at a distance from a pivot point. This calculator works out torque in newton-metres (Nm) from the applied force in newtons (N) and the length of the lever arm in metres (m). It is a universal physics and engineering tool used for tightening bolts, sizing motors, balancing levers and analysing rotating machinery.

How to Use It

Enter the force in newtons and the perpendicular distance (lever arm) in metres, then read off the torque. For example, pushing with 100 N on a 0.5 m wrench produces 50 Nm. If your force is given in kilograms-force, multiply by 9.81 to convert to newtons first. The distance must be measured perpendicular to the line of the force for the result to be exact.

The Formula Explained

The equation is $$\tau = F \times d$$ where \(\tau\) is torque in newton-metres, \(F\) is force in newtons, and \(d\) is the distance from the axis of rotation in metres. Because one newton-metre is one newton applied one metre from the pivot, the units combine directly. A larger force or a longer lever arm both increase torque, which is why long-handled wrenches loosen stubborn bolts more easily.

Advertisement
Wrench on a bolt showing force F at the end of a lever arm of length d producing torque tau
Torque is the force F applied at a perpendicular distance d from the pivot.

Worked Example

A mechanic applies 250 N at the end of a 0.4 m wrench. $$\text{Torque} = 250 \times 0.4 = 100 \text{ Nm}$$ To reach a target of 150 Nm with the same wrench, the force needed would be \(150 \div 0.4 = 375\) N.

Lever example with 50 newton force at 0.3 metres giving 15 newton-metres of torque
Example: 50 N applied at 0.3 m gives a torque of 15 Nm.

Torque Unit Conversion Table

Torque is a force multiplied by a distance, so its units are a force unit times a length unit. The table shows how common torque units relate to the newton-metre (Nm), the SI unit.

From To Factor
1 Nm lbf·ft (pound-force foot) 0.7376
1 Nm lbf·in (pound-force inch) 8.8507
1 Nm kgf·m (kilogram-force metre) 0.10197
1 Nm kgf·cm (kilogram-force centimetre) 10.197
1 Nm mNm (millinewton-metre) 1000
1 Nm kNm (kilonewton-metre) 0.001
1 lbf·ft Nm 1.3558
1 lbf·in Nm 0.11298
1 kgf·m Nm 9.80665

To convert, multiply the value by the factor in the row. For example, 50 Nm × 0.7376 ≈ 36.88 lbf·ft.

Typical Torque Values

The figures below are rough, approximate values. Actual torque depends on the specific application, so always follow the manufacturer's specification.

Application Approximate torque
M8 bolt tightening (typical, depends on grade and lubrication) about 25 Nm
Car wheel lug nuts (varies by vehicle) about 90–120 Nm
Small cordless drill (working range) about 1–10 Nm
Typical passenger car engine, peak torque about 150–400 Nm
Bicycle pedal tightening (pedal thread into crank) about 30–40 Nm

These are guide values only and are not a substitute for the torque figure in the relevant manual.

Advertisement

Torque Under Different Force and Lever Arm Combinations

Torque is \(\tau = F \times d\). With a fixed force, torque grows in direct proportion to the lever arm. For a fixed target torque, a longer lever arm needs proportionally less force.

Lever arm (m) Torque from a constant 100 N force (Nm) Force needed for 100 Nm (N)
0.1 10 1000
0.25 25 400
0.5 50 200
1.0 100 100

Worked check for the required force: at 0.25 m, \(F = \tau / d = 100 / 0.25 = 400\) N. Applying that force back gives \(\tau = 400 \times 0.25 = \) 100 Nm.

This is why a longer wrench makes a tight bolt easier to turn. It assumes the force is applied perpendicular to the lever arm. At other angles only the perpendicular component contributes.

FAQ

Is a newton-metre the same as a joule? Numerically yes (1 Nm = 1 J), but torque and energy are physically different quantities, so torque is always written as Nm, not joules.

What if the force is not perpendicular? Use the perpendicular component of the force, or \(\tau = F \times d \times \sin(\theta)\), where \(\theta\) is the angle between the force and the lever arm.

How do I convert Nm to foot-pounds? Multiply newton-metres by 0.7376 to get foot-pounds (\(\text{lb}\cdot\text{ft}\)).

Last updated:

Most popular in Physics and Engineering

View all Physics and Engineering calculators