265 calculators

  • Principal Stress Calculator
    Calculate principal stresses σ₁ and σ₂, maximum shear stress, and principal angle from σx, σy, and τxy using the 2D plane stress equations.
  • G Force Calculator
    Convert acceleration (m/s²) into G-force using standard gravity (9.80665 m/s²). Fast, free G-force calculator with the formula and worked examples.
  • Compression Ratio Calculator
    Calculate engine compression ratio (CR) from bore, stroke and clearance volume. Computes swept displacement and CR instantly for any cylinder.
  • Parallel Axis Theorem Calculator
    Calculate moment of inertia about any parallel axis using the parallel axis theorem I = I_cm + m·d². Enter I_cm, mass, and axis distance.
  • Heat Transfer Coefficient Calculator
    Calculate the convective heat transfer coefficient h = Q/(A·ΔT) from heat rate, surface area, and temperature difference. Free, instant, in W/(m²·K).
  • Shear Modulus Calculator
    Calculate shear modulus (modulus of rigidity, G) from shear stress and strain, or from Young's modulus E and Poisson's ratio ν.
  • Pulley Calculator
    Free pulley calculator using D1×N1 = D2×N2. Solve driver/driven pulley diameter, speed (RPM), or belt speed ratio by entering any three values.
  • Fixed-End Beam Deflection Calculator
    Calculate the maximum deflection of a beam fixed at both ends under a central point load, off-center point load or uniform load, plus fixed-end moments.
  • Biot Number Calculator
    Calculate the Biot number (Bi = h·Lc/k) from convective coefficient, characteristic length and thermal conductivity to check lumped capacitance validity.
  • Torque Wrench Extension Calculator
    Calculate the adjusted torque wrench setting when using an extension or crowfoot. Enter desired torque, wrench length, extension length and angle.
  • Pulley RPM & Speed Calculator
    Calculate driven pulley RPM from driver pulley diameter, speed, and driven diameter using N2 = N1 × D1 / D2. Find belt drive ratio fast.
  • Final Velocity Calculator
    Calculate final velocity from initial velocity, acceleration and time or distance using the kinematic equations. Results in m/s, km/h and mph.
  • Servo Torque Calculator
    Estimate servo torque from operating voltage, current, and speed (RPM). Uses electrical power and RPM to compute torque for quick motor sizing.
  • Torsion Spring Calculator
    Calculate the torsional spring rate of a helical torsion spring from wire diameter, coil diameter, active coils, and modulus of elasticity.
  • Gravitational Force Calculator
    Calculate gravitational force between two objects with this Gravitational Force Calculator. Input masses and distance to determine the attraction force instantly.
  • Thermal Stress Calculator
    Calculate thermal stress in a fully constrained material from Young's modulus, thermal expansion coefficient, and temperature change using σ = E·α·ΔT.
  • Outboard Propeller Pitch Calculator
    Find the outboard propeller pitch that hits your target boat speed at a given engine RPM, gearcase ratio, and prop slip. Free, instant prop pitch sizing.
  • Force Calculator
    Calculate force from mass and acceleration using Newton's second law (F = m·a). Enter mass in kg and acceleration in m/s² to get force in newtons.
  • Effectiveness-NTU Calculator
    Compute NTU, capacity ratio, and counterflow heat-exchanger effectiveness from UA, Cmin and Cmax with the ε-NTU method.
  • Young's Modulus Calculator
    Calculate Young's modulus (E) of a material from applied force, cross-sectional area, original length and change in length. Get stress, strain and E in Pa & GPa.
  • Winch Size Calculator
    Calculate the minimum winch capacity for your vehicle using its weight and a safety factor. Find the right rated line pull for safe recovery.
  • Uniform Velocity Motion Distance Calculator
    Compute travel distance from constant speed and elapsed time with d = v × t. Enter speed in km/h, m/min or m/s plus hours, minutes and seconds.
  • Thermal Conductivity Calculator
    Calculate thermal conductivity k from heat transferred, thickness, area, temperature difference and time using Fourier's law of heat conduction.
  • Surface Feet per Minute (SFM) Calculator
    Calculate SFM (surface feet per minute) from RPM and tool diameter, or solve for spindle RPM from a target cutting speed. Free machining speed tool.